When you need a furnace repair or a tune-up, there is no better place to turn than Point Bay Fuel. All of our technicians have years of experience which means they are fully qualified to complete all types of HVAC service. We service Toms River NJ and surrounding areas.
Their expertise spans from new furnace installation, repairs, and maintenance. The NATE certification that they hold provides them with an understanding of all aspects of the work. We service every make and model of heater, and we do this at an affordable price. You can count on us to provide you with fast, friendly, and professional service each and every time.
We stand by the work that we do and ensure that your satisfaction is guaranteed. We also offer free estimates and second opinions. Give us a call today to set an appointment. We will take the time that you need to answer any questions that you may have about your heating or cooling system.
What Causes A Furnace To Blow Cold Air?
It is frustrating when a heating system malfunctions. However, certain signs let you know when something is going wrong. While furnace troubleshooting, you might notice your furnace isn’t blowing hot air at all. Instead, it’s blowing cold air. The reason behind a heater blowing cold air is what we’ll be discussing in this article.
Flame Sensor Or Pilot Light Malfunction
Most modern furnaces have an electronic ignition system. However, the ignition on older models is typically a pilot light. When the pilot light malfunctions on a heater, cold air is all it can blow. The pilot light is the first thing to check when an older furnace blows cold air. You can light it again, but if the pilot light continually goes out, there is something else that is wrong. A professional inspection and cleaning are in order, along with any needed repairs.
A furnace that relies on a flame sensor to heat the air has an electronic ignition system. If the flame sensor on modern furnaces get dirty or becomes defective, the heater will blow cold air. Calling in a professional HVAC technician to service these units is the best idea and will result in a resolution. However, the do-it-yourself technique is often fraught with failure. A professional will inspect the heating system and correctly identify what’s wrong. When shopping for furnace repair near my location, make sure to look for one with a good reputation and lots of experience.
When ductwork is worn or damaged, it allows conditioned air to escape.
The amount that escapes depends on the level of the damage, or holes. The untrained eye may not be able to realize this issue since ducts are typically hidden inside walls and ceilings and under floors. According to the DOE, average homes lose between 20% to 30% of conditioned air to leaky ducts. This reason is why, if you have old ductwork, a professional HVAC technician should inspect it.
Clogged High-Efficiency Vent Pipes
Vent pipes on high-efficiency furnaces usually are placed on the outside of homes. For this reason, they can accumulate ice, snow and other debris which causes them to become clogged. It can also sometimes explain why heaters blow cold air or shut down.
When the thermostat fan is in the “on” setting, the blower will constantly blow air even though the furnace may be off. It’s easy to resolve this by switching it to the “auto” setting instead. The auto setting only allows the blower to work when the heating system turns on.
When a furnace overheats…
the limit switch, which is a safety feature, will turn the burners off allowing the appliance to cool down. During this time, the furnace will blow cold air. A dirty filter is the main reason for this problem and is one of the main reasons you should change or clean the air filter regularly. Dirty filters cause a heater to work harder than it should, and that leads to higher energy bills. You can make your heater last longer by replacing the filters.
Furnace Repair Toms River NJ
Here are some reasons your furnace might be blowing cold air instead of hot air:
- Clogged vent pipes
- Leaky ducts
- Incorrect thermostat settings
- Pilot light or flame sensor malfunction
To maintain your heater in good working order…
hire a well-trained and qualified professional HVAC technician to inspect, clean and repair it on a regular basis. Hiring a professional is particularly important because they can quickly identify potential problems in the formative stage before they become more complicated and more expensive. Working with the best furnace repair service in your area is imperative.
When choosing a furnace repair near me, contact Point Bay Fuel. All our technicians can inspect your furnace and diagnose the problem that is causing it to blow cold air. They are highly trained and will provide you all the information about your heating situation. You’ll learn about your options so that you can make a proper decision about what’s right for your home.
It can become very uncomfortable during the winter when the heating system malfunctions. For this reason, you should act quickly at the first signs of a faulty heating system. We offer affordable furnace repair cost and friendly service. Call us today.
Some of the areas we service include Beachwood, Brick, Ocean Gate, Toms River and these zip codes: 08722, 08723, 08740, 08753 as well as all surrounding areas in Jersey Shore.